Well now.. You sure did some from nowhere, I do hope you can put together what's needed..
Hello there, my name is Rachel. I've been asked by my sister to go over what we need for the next step of the mag-propulsion system which is being modified from the Mark 0, I do hope she knows what she's doing.
I'll begin with a few excerpts from my log files when I was making the thing. Since you're only handling on specific part, this shouldn't be too bad in the long run. Direct your attention to the quote below, it should give a general idea on what this piece is needed to do.
Rachel Snow - Injector Stream - Part 2 Wrote:After being directed out of the Separator and Particle Distributor, the graviton or anti-graviton stream - dependening on the needs of the propulsor - enter the Injector Assembly Image. Inside the injector assembly, the injector array components use micro-helical impellers to hyper accelerate the graviton anti-graviton stream into a Coalesced-Charged Graviton or Anti-Graviton Stream. Due to the Hanks-Katsumi Graviton/Anti-Graviton Acceleration Principle, graviton and anti-graviton streams hyper accelerated in the injector impeller warp into a graviton/anti-graviton field stream with constituent particles phasing in and out of particle and energy form. This stream also adopts a electrical charge as background energy around it is stressed and subsequently excited. This Coalesced Stream is then directed through two nodes - the Alpha and Beta node - which produce two opposing streams that then enter the Main Impeller.
Luckily for you, the electronics which are required to drive the system have already been completed. Focusing the streams from the distributor system can be done with multiple superconductive tubes. One for each. On top of that, you'll need a few boards soldered onto the system. The schematics for the boards has been attached below. Giving that to Lividia or something should get them processed easily enough, they should have the systems for making this sort of thing. The actual pieces that go inside of the system i'll put in myself, that's something i'm not willing to share out currently.
Beyond that, a piece of hardware which can handle the forces it'll experience inside, as well as being shaped properly as an injector node is all that we require. I'll be looking forward to your work. Thank you.
Heeeeey! I'm sorry about her, Rachel isn't really the best at being.. 'open' or 'friendly' when she doesn't know you. She probably was a bit direct, huh..
Since she obviously isn't going to give you a copy, I will. I'm going to forward over an image of what the simulated image of the Mark 0 on the Feanturi looks like. It should give 'some' idea on what you're supposed to be doing.
If you have any questions, feel free to respond back. I'll try to grab the message before Rachel does. Remember, all I need you to work on, is the injector array.
I must admit I am pretty impressed by the project and overall copy material. I think you are trying to work over something that was once about to be tested by Kishiro Technology several centuries ago, but the project has been dropped as soon as Kusari Empire made contact with Liberty and their megacorporation, namely Ageira Technologies. The said technology was purely theoretical, however I do believe there should be some scraps of information in the Kusari Republic Databases. The name would be the "Phased Array Gravity Drive" also known as the "Impeller Drive"
What I found right now about said engine are just scraps of information, since database is pretty old and not really accurate.
Kusari Republic Database, 4th to 5th Century - Translated, Modified Entry
The impeller drive would create a pair of stressed gravity bands above and below a ship, known as the impeller wedge. In order to generate the wedge, a pair of impeller rings, located at the fore and aft ends of the ship, would be required.
<...>
An impeller ring, also sometimes called an impeller band, should be a ring structure made up of numerous beta nodes. The two rings at the bow and stern of a vessel coming together to form the impeller wedge.
<...>
The wedge would become a pair of extremely powerful gravity bands located above and below the generating ship. Both bands could be inclined such that the forward end, or "throat", is far deeper than the aft end, the "kilt". The wedge could be capable of accelerating a vessel to near-light speed.
<...>
Due to the immense twisting and warping of space that would occurr in the band, no known weapons could be known to penetrate an impeller wedge in either direction. The dorsal and ventral aspects on the other hand would be invulnerable to attack as long as the wedge was up. The flanks, forward, and aft aspects of the vessel would be exposed.
<...>
A wedge are supposed to be much larger in length and width than the ship that generated it. On a ship of the wall, width of the wedge could be measured in hundreds of kilometers, requiring plenty of distance between ships in formation.
A quite complicated thing, but I do believe some of these info could be easily taken about. Aside of the fact that some say such a technology would act both as a shield generator and propulsion drive, even without using the Jump Gates, the project was halted as soon as Jumpt Gate and Trade Lane technology has been introduced into Kusari.
Kind of shame, but I think it were the money that decided about it.
I will search for the potential resolve to the injector array problem of yours, then I will spend some time over the construction of such a device - or something quite similiar to it.
Our designs are not the same as what you've described, I presume you'll know not to try to make a copy of what they have in their database. That's quite interesting however. If they didn't have one of the resources we do now, that i'd consider be the next best available way of going about propulsion using this method.
Our designs are already complete. We don't need to work on solving a problem, merely bringing it about to existence.
I'll be looking forward to what you are able to work out. Thank you again.